home |

company profile |

product |

contact us |

 enquiry
 
   

                                                                                   
ABOUT OUR PRODUCT
All liquid Resin Properties are tested as per IS:6746,though actual value can
vary within standard tolerances as per IS:6746.Gel times are tested with
catalyst (MEKP-50%) 1.5% and Accelerator (Cobalt Octate 2%)1.5%. Gel
times for SMC/DMC Resin are tested with BPO 2% paste. It is advised that
the Resin should be stored at temperatures below 30 degree C in tightly closed
containers. Exposure to sunlight should be avoided to prevent the Resin from
pre mature gelation, even when no catalyst is present.
The standard Packing sizes are 25kg plastic Jerry Cans and 200kg M.S. Drum/Plastic Drum. Listed below are the standard grades, Resins however can be formulated for any desired properties not covered here.

SPECIFICATION OF RESIN

Grades of Resin

Liquid Resin Properties

  

CAST RESIN PROPERTIES

  

SUGGESTED APPLICATION
  Appearance

Sp. Gr. at
250 C

Viscosity at (CPS)
250C

Acid Value mg KOH/G

Volatile
Content
(W/W)%

Gel Time at 250C
(Minutes)

  

HDT
C

Barcol Hardness

Tensil Strength N/mm2

Flexural Strength N/mm2

Water Absorption(%)
250C 24 hours

      

ORTHOPTHALIC ACID BASED

                          
SPL-101 Colourless to pale yellow liquid 1.1-1.2 500-600 25 +/- 3 35-37 15-20   70 44 58 110 0.10%   General Purpose Hand lay-up for Superior Mouldings and Structural Applications
SPL-111 Hazy Liquid 1.25 Thixo-Tropic 25 +/- 3 30-32 20-25   70 44 58 110 0.10%   General Purpose Gelcoat with good weather resistence
SPL-121 White Hazy Liquid 1.2-1.3 600-800 25 +/- 3 32-35 15-20   70 44 58 110 0.10%   Application conforming to General Purpose, very low flammability
SPL-131 Clear Viscous Liquid 1.1-1.2 1000-1200 18 +/- 2 30-33 15-20   65 48 60 115 0.10%   Superior General Purpose SMC/DMC for Hot Press Moulding
SPL-141 Colourless to Pale Yellow Liquid 1.1-1.2 180-250 20 +/- 2 38-40 15-20   70 42 65 120 0.17%   General Purpose Resin Transfer Moulding (RTM) application
SPL-201 Colourless to Pale Yellow Liquid 1.1-1.2 200-250 25 +/- 3 36-38 15-20   70 40 54 100 0.10%   Hand lay up Rooflite Sheet Making Resin for Superior Translucency and weather ability

ISOPHTHALIC ACID BASED

                          
SPL-301 Pale Yellow Liquid 1.1-1.2 600-800 16 +/- 2 34-37 15-20   95 45 55 115 0.10%   Isophthalic Resin for mechanical and chemical resistance properties, suitable for Tank lining,filament winding
SPL-321 Off-white opaque Liquid 1.1-1.2 800-1000 16 +/- 2 32-35 15-20   95 45 55 115 0.10%   Isophthalic Fire retardant with low flammable rating (type-5) and with chemical resistance
SPL-341 Colourless to Pale Yellow Liquid 1.1-1.2 200-250 16 +- 2 38-40 15-20   95 45 55 115 0.17%   Isophthalic Resin Transfer Mouliding (RTM) application
                             

Please note that the information contained in this page is based on experimental work done in our laboratories and is believed to be correct to the best of our knowledge. However, since conditions under which our products may be used are beyond our control, recommendations are made without warrant or guarantee
 
   
   
   
   

Copyright © Sha Polychem Private Limited. All Rights Reserved.